Table of Contents
What angle do you cut crown molding for cabinets?
Cut the Molding with the Miter Saw Adjust the miter saw to cut at the correct 45-degree angle taking into account when cutting that, since the molding is being held upside down, that the “bottom” of the molding is actually the top.
Can you glue crown molding to cabinets?
Provide a nailing surface for crown moulding by attaching solid wood mounting strips to the top edges of the cabinets. Cut strips of straight 3/4-in x 1-1/2-in wood to fit the front and sides of each cabinet. Then apply wood glue to each strip, nail it in place, and let dry.
Do you glue or nail crown molding?
Crown is typically nailed up with a 2” finishing nail and a compressor and finishing gun. Outside corners are usually done with a brad nailer and 1” brad nails with glue. Studs are generally 3-1/2”, drywall a ½” and the crown moulding a minimum of ½”; therefore 2” finishing nails are necessary.
What side of crown molding goes up?
Crown moulding is installed in the reverse fashion of base moulding. The deeper grooves go on the bottom, and shallower grooves belong on the top. Generally, crown moulding extends further down the wall than on the ceiling. The concave (cove) side goes down, and the convex (rounded) side goes up.
Where do you nail crown molding?
Crown molding is usually nailed to the wall studs along the bottom edge and into the ceiling joists above–a lot of stud-finder work.
Is installing crown molding difficult?
Compared to wood, foam crown molding is not only affordable and easy to install, but it’s also pliable—making it easy to work with around the curvatures of your home.
How do you measure and cut crown molding for cabinets?
Measure a piece of crown molding equal to the length of the cabinet. Place your tape measure on the edge of the crown and extend it to the length of one cabinet side. Use a pencil to mark the exact spot that needs to be cut. Repeat for each cabinet side.
How do you cut crown molding for upper corner cabinets?
To cut crown molding inside corners, start by measuring the angle of the corner using an adjustable protractor, and setting a compound miter saw to the correct angles. Next, place the piece of crown molding in the jig and the bed of your saw to cut the right inside corner.
How do you fill the gap between kitchen cabinets and ceiling?
You can build the cabinets to the ceiling (most expensive option), keep the area open (no cost!), build a soffit to match the cabinets, or add a drywall soffit.
Can you glue crown molding instead of nailing it?
The use of both provides combined strength while reducing nail holes. The nails in the combination method will hold the adhesive in place for a smooth drying process. Conversely, glue in a combination method will hold the crown molding in place while you complete the nailing process.
Do I need adhesive for crown molding?
It is important to put an adhesive (Loctite’s Power Grab, PL Premium, etc.) on both edges of the molding (ceiling and wall) and on the seam between each piece. This helps to hold the crown molding up during installation and, more importantly, will prevent the crown molding from ever separating.
Will Liquid Nails hold up crown molding?
High Density Recycled Polystyrene Crown mouldings can be glued, nailed or both. It cuts just like wood and it also copes just like wood. Apply a continuous ¼” bead of Heavy Duty construction adhesive such as Liquid Nails LN-901 along the back edges of the crown moulding. Make sure to glue all joints.
Can crown molding be installed upside down?
Crown molding can be installed upside down, although it is usually not recommended. If you like the unconventional style and keep it consistent throughout your home, there is a chance that your guests may not even notice your alternative design.
How far down the wall does crown molding go?
For standard 8-foot-high ceilings, the crown/cornice height should be 2½ to 6 inches; for 9-foot ceilings, 3 to 7½ inches, and for 10-foot ceilings, 3½ to 8 inches.
Do you have to cut crown molding upside down?
It’s a best practice to cut crown moulding upside down on the miter saw. The moulding has flat edges where it touches the wall and ceiling. Use these “flats” to keep the piece firmly in position on the saw’s base and fence when making a cut.
Does crown molding have to be nailed into studs?
Crown moldings, or any corner trims really should be nailed to a stud, not simply into unbacked drywall. Without good support, the molding will warp out from the wall causing gaps in coverage to open along the edges.
Can I use 18 gauge nails for crown molding?
18 gauge should work fine unless you’re putting on a really huge crown mold. 15 gauge is meant more for doing outdoor trim, like window trim or corner board. 16 gauge might be a little big if your trim is thin, you risk having a split, and the holes to fill in will be bigger.
Can I glue crown molding?
Apply Loctite Power Grab Molding & Paneling Adhesive to the back of the molding, keeping at least 1/2″ from the edge. Place the trimmed end of the crown molding on the wall next to the corner. The adhesive will keep the molding or trim in place while you tack it in place.
How much should I pay for crown molding installation?
The average cost to install crown molding is $7 to $16 per linear foot depending on the materials chosen and labor costs. For an average living room, crown molding costs $464 to $1,102, while a kitchen costs between $210 to $570, and an entire home costs between $2,000 and $4,000 for both labor and installation.
Should you paint before installing crown molding?
You can paint the walls before or after installing the molding. However, painting prior to installing the molding has an advantage in that you do not need to protect the molding with painter’s tape and can paint more quickly without worrying about getting paint on your molding.
