Table of Contents
How do you calculate stair stringers?
How do I calculate a stair stringer? Start by finding the overall height that the staircase will be. Decide the height or “rise” you’ll want for each step. Divide the total height of the staircase by the height or “rise” you want for each step.
Can I use 2×10 for stair stringers?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
How do you make a stair stringer from scratch?
How to Build Stair Stringers Step 1: Set Stair Measurement on Square. Step 2: Mark the Top Cutting Line. Step 3: Mark the Cutting Line. Step 4: Finish Cut With a Jigsaw. Step 5: Trace an Open Stringer. Step 6: Attach Stair Angles. Step 7: Attach Stairs From Underside.
What size lumber is used for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has .
How far apart do stair stringers need to be?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
What is the formula for building steps?
You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14). Next, you divide the height by the number of treads (15 into 106), producing the exact tread height (7.06 inches).
Can I use 2×12 for deck stair treads?
Stair treads may be made of a single 2×12, but are often made of two decking boards or 2x6s. A stringer is a wide board, usually a 2×12, that runs at an angle from the landing pad to the deck framing and supports the treads. The stair treads should be at least 36 inches wide.
How long should a 2×12 stringer be?
How to Use the EZ Stair Calculator. We suggest 10.5″ for 2×12 or 2 – 2×6 Treads. Treads may be cut to suit other widths.
What is the code for stair stringers?
Stair stringers should not span more than 13 feet and 3 inches (4039 mm) for a closed stringer. Cut stringers should not span more than 6 feet (1829 mm). Refer to the American Wood Council’s 2018 Prescriptive Residential Wood Deck Construction Guide for stringer spans.
What angle should stair stringers be?
Stair codes and guidelines prefer an angle of around 37° for normal stairways (the green area in our illustration) and around 7° for ramps (the yellow area in our illustration).
Can you use joist hangers for stair stringers?
This will reinforce the stair stringer to rim joist connection and distribute the stair weight more evenly onto the deck framing. Cut them to fit the space perpendicularly between the rim joist and the next interior joist. Use joist hangers to fasten the blocking.
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
How many steps are in a 4 foot deck?
A four-foot high deck can have a range between 6 and 8 steps.
How do I calculate how many steps I need?
Divide the rise by 6 or 7 inches (15 or 18 cm) to find the total number of stairs. For larger stairs, divide by 6 and for smaller stairs, divide by 7. The total you get is how many stairs your future staircase will have so you can plan accordingly.
What is the standard step height for stairs?
Riser Heights In the United States, the step height standard should be between 7 or 7 ¾ inches at the most, and no less than 4 inches. You should follow other measurements if given by local building codes. In Canada, the maximum step riser height is 8 ¼ inches.
How high is a 2 step Stringer?
Size:2 In. Step stringers are cut for 2″ X 12″ Treads, and have a 7″ Rise.
How tall is a 5 step Stringer?
Stair Stringer-5 step Redwood (Common: 60 in. x 11 in.; Actual: 1.5 in.
What is building code for stairs?
The IRC stairs code states that, to comply with stairway requirements, the minimum width for residential stairs be no less than 36 inches. The stair riser code is up to 7.75 inches, and can not vary more than 3/8 of an inch. There are also section codes in place for standard stair tread dimensions.
Why do stair treads crack?
Wood stairs utilize thick stair treads for stability. These hardwood treads can be between 1 1/2 to 2 inches in thickness. When wood is cut this thick, it can split due to humidity changes. Once a stair tread is split or cracked, you can’t glue it back together.
What is the best wood for stair stringers?
LP SolidStart Laminated Strand Lumber (LSL) and LP SolidStart Laminated Veneer Lumber (LVL) are ideal for Stair Stringers because they surpass traditional lumber products in length, strength and consistency.
How tall is a 4 step Stringer?
Mendocino Forest Products Stair Stringer 4 step Redwood (Common: 48 in. x 12 in.; Actual: 1.5 in.
Do you put risers or treads first?
When installing stairs, install the riser first, and then the tread. Start at the bottom of the stairs and work your way up, alternating risers and treads. The back of each tread will sit flush against the riser.
What Lumber Do I need to build steps?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
What size should deck joists be?
Commonly used joist sizes are 2-by-6, 2-by-8 and 2-by-10. For example, when you space joists 16″ apart — which is standard for residential decks — a deck spanning 9 1/2′ would require 2-by-6 joists, a 13′ deck would need 2-by-8 joists and a 16′ deck calls for 2-by-10 joists.
