Table of Contents
What tool do I need to make tongue and groove?
Tongue-and-groove joints are commonly made on a table saw. But with the right bits, the joints can be made just as easily on a router table.
How deep should a tongue and groove joint be?
The groove should ALWAYS be slightly deeper than the tongue is long, by as much as 1/16″ for 3-inch wide boards. The reason for this is two-fold. First is to prevent problems during assembly.
Is a router plane useful?
Router planes, which are more like shoulder planes than routers, are invaluable for cleaning up and trimming tenon cheeks and other joinery, hinge mortises, inlay mortises, and more. But to do its best work, this small plane must be properly tuned. Learn how to get it that way, and how best to use this handy plane.
What router bits are needed for tongue-and-groove?
Step 1: Generally speaking, it’s easier to cut the groove of a T&G joint first, then mill the tongue to fit the groove. A 1/4-in. straight bit or spiral upcut bit makes an ideal groove-cutter into the edge of a workpiece.
How do you make wood ridges without a router?
Alternative Ways to Cut Grooves (Rabbeting) Table Saw Method. Typically, grooves cut into wood on a table saw are cut using a dado blade. Dremel Tool Method. Rabbeting Plane. Chisel Method. Rounding and Chamfering with a Plane. Using Molding Planes. Molding with a Scratch Stock. Keyhole Slot.
Should tongue and groove be glued?
The recommended glue for floating installation is Tongue and Groove engineered flooring glue. Glue placement is very important. The glue must be placed along the topside of the groove the full length of the grooved side and end.
Are tongue and groove joints strong?
A tongue-and-groove is stronger than simple butt joints due to the increased gluing surface and mechanical interlocking of the two mating pieces. As a bonus, the tongue also serves to perfectly align the workpieces during the glue-up for a smooth surface.
What bit should I use to make a groove router?
A chamfer bit is also used to create V-shaped grooves between boards (when two chamfers meet edge to edge they form a V-groove). Chamfer bits come in various sizes and a few different angles. We’d recommend one with a 1-1/4-inch diameter. This is a nonpiloted router bit that cuts round-bottomed grooves.
What is a dado plane?
Dado Plane – 1/4 inch This 1/4″ Dado Plane is used to make a 1/4″ dado (groove) across or with the grain. The precision made nicker ensures a very neat and accurate dado as the wood fibers are cleanly severed ahead of the blade when planing across the grain.
How do you cut wood without a power saw?
A knife works best for thin pieces of wood. Grasp the wood firmly or use a vice, then cut with a slanted angle. A knife won’t work as well if used straight on the wood. Slide the knife back and forth with even pressure and tempo.
How do you cut a hole in wood without going all the way through?
I usually just wrap a piece of masking tape around the drill bit leaving the correct length exposed. You can either wrap enough layers of tape around so that it is fairly thick, or leave a “flag” of tape sticking out. Either way will let you drill to the proper depth without the risk of marking the surface.
What tool makes a groove in wood?
If you want to cut a groove in a piece of wood, a plunge router is the easiest tool to use for straight or curved grooves. Using a rotary tool also works for cutting short channels, but it’s more difficult to make long, straight lines with them.
How thick is tongue and groove?
STEP 1: The usual convention for building tongue-and-groove joints is to cut the groove (or dado) first, then mill the tongue to fit it. Although the proportions of the joint parts can vary, usually the width of the groove is 1/3 the thickness of the mating part. So, on 3/4-in. stock, make your groove 1/4-in.
Do you nail through the tongue or groove?
For tongue-and-groove flooring, drive a nail at a 45-degree angle through the tongue, then conceal it by engaging the groove of the next board. Be sure to countersink the nail — drive it slightly below the surface of the wood — to prevent interference in the joint.
Does the tongue or groove go against the wall?
Which to Install First. Which side is the tongue, which the groove, and which goes first during installation? The tongue is the side that you will want to place against the wall as you start your laminate-flooring installation.
Can I use wood glue for tongue and groove?
1 Answer. This looks like a simple white wood glue. That should be no problem here. Do NOT use a polyurethane wood glue here like Gorilla glue, as that will expand out and cause a mess, as well as possibly push the boards apart.
What are the disadvantages of a tongue and groove joint?
The single disadvantage might be that the joint is visible from the end of the panel. The tongue-and-groove joint is often used to form wider panels from narrower boards, such as when forming table tops, doors, or architectural paneling. It’s also widely used for strip flooring.
Can tongue and groove be used outside?
T&G Wood Siding is a best seller because of its versatility. It can be used indoors or outdoors, rough side or smooth side, installed horizontally, vertically or diagonally, to provide distinctly different looks.
What are the 3 key advantages of a tongue and groove joint?
The primary advantage of a tongue and groove joint is its stability. Flat surfaces receive strong support because it offers three strength layers where it joins. This type of wood joinery also provides a lot of area for adhesives. The larger the area you can apply the wood glue stronger the bond will be.
