Table of Contents
When using acetone or paint thinner for thinning epoxy, the general rule of thumb is a maximum of 10% added to the epoxy resin. An example would be if you had 32 ounces of epoxy that you were mixing you would only add up to 3.2 ounces of acetone to that mixture. Recommend over acetone and other solvents.
What kind of thinner do you use for epoxy primer?
What is Thinner 200 used for? Epoxy Primer Thinner 200 is used as a thinner for 2-part epoxies like TotalProtect, Aluminum Boat Barrier Coat, and 2-Part Epoxy Primer systems (surfacing, high-build, and clear). It is also used as a pre-paint surface prep solvent for inflatable boats, and to clean painting equipment.
What can I use to thin epoxy?
Method #2: Thinning Epoxy Resin Using a Solvent Solvents like denatured alcohol, lacquer thinners and acetone. All of these solvents are easily available and also do a great job in lowering the viscosity. Also, these solvents evaporate quickly and are unlikely to become trapped in your cured epoxy resin.
Do I need to thin epoxy primer?
You need to thin the epoxy (by the remendations) and maybe better gun or smaller tip to get it to atomize better. But this is standard practice in collision shops all over the country. It works, so SOMETHING you are doing is wrong.
Can I add reducer to epoxy primer?
Yes a slow reducer will allow the primer to go on more smoothly and dry more slowly. Yes a slow reducer will allow the primer to go on more smoothly and dry more slowly.
What is the next step after epoxy primer?
1. Sand, recoat with epoxy primer again, sand, and spray with paint. 2. Sand, lay down some 2k primer, sand, and spray with paint.
What color is epoxy primer?
A primer makes the concrete ready for the next stage. Whereas, the ‘Indigo Paints’ epoxy primer is a sealer that binds the concrete with the paint. A primer is mostly white or neutral in colour.
Why is my epoxy so thick?
Temperature The ideal room temperature for mixing ArtResin epoxy resin is between 75 and 85 degrees F or 24 – 30 degrees C. If it’s colder than that, the resin will be thicker and harder to mix, will have more bubbles and will take longer to cure until it’s dry to the touch.
Can you thin epoxy with mineral spirits?
3. Denatured Alcohol. Denatured alcohol is ethanol that has been made poisonous, but it’s a solvent that is safer to use as resin thinner than paint thinner or acetone. It’s properties also allow you to thin the epoxy more without as much detriment to its protective nature.
How do you thin TotalBoat epoxy?
TotalBoat Penetrating Epoxy can be thinned up to 100% with acetone, denatured alcohol, or lacquer thinner*. Always mix the resin and hardener epoxy components together prior to adding any solvents.
Will acetone damage cured epoxy?
Use enough acetone to soak into the surface a bit. Be careful not to damage the wood/concrete as you use your knife or scraping tool to gently and slowly scrape off the epoxy resin. There is no need to worry about any wet areas left by the acetone as it will evaporate on its own.
Can I thin epoxy with xylene?
Xylene – Xylene is very compatible with epoxy and is often used by the manufacturers to thin resins and hardeners to the right consistency. If you look on the side of a Xylene container, you will find that a recommended use for Xylene is to clean and or thin 2-part epoxy paints etc.
How do you liquify epoxy resin?
Use the heat gun at a temperature of about 90 °C, aiming it at small areas of the epoxy until it softens. You can then use a plastic scraper to remove the epoxy. Use chemicals. If you’re removing epoxy from plastic or glass, you can use chemicals to soften the epoxy, and then scrape it away.
How do you use epoxy primer as a sealer?
Use it For a Final Sealer – A cool trick we’ve been doing for the past few years is using our epoxy primer as a final sealer before our base coat. Simply reduce it 50 percent and lay a coat or two down to seal up all of your work and have a nice surface to lay your base coat over top of.
How many coats of epoxy primer do I need?
The epoxy primer should be applied in medium wet coats, allowing a half an hour between each coat at around 70 degrees. One to two coats will render a one millimeter dry film thickness, which is typically enough to be completely effective.
What is the difference between epoxy primer and urethane primer?
Since urethane is only a primer surfacer, you’ll also need to apply a sealer before you paint. Again, a coat of epoxy primer over the top will serve the purpose. Filler primer paints are basically formulated to fill in any pits in the surface from sanding or rust even quicker than an epoxy primer alone.
What is the purpose of epoxy primer?
Epoxy primer is a sealer that produces a good surface finish on applied top coats. A two-part epoxy primer contains zinc phosphate, which acts as a corrosion-inhibiting pigment. Epoxy primers can be used to waterproof materials that consequently protect the bare metal from oxidation.
Does epoxy primer color matter?
Any color primer will work but you will need to apply more paint the more contrast there is between colors.
Can I tint epoxy primer?
NeverStrip Epoxy Primer can be tinted in any of the “W” Colors on this Color Chart. Typically, this product is the first coat of a NeverStrip Color System to transform a floor. NeverStrip Color (Thin Film Urethane) is then applied to the epoxy primer with the color being any of the available colors on the Color Chart.
What is a epoxy paint?
What Is Epoxy Paint? Originally designed for industrial use, epoxy paint is a latex acrylic product that may have a small amount of epoxy in the mix and is used for flooring applications. Epoxy paints provide a tough, durable protective coating that’s easy to maintain.
