Table of Contents
Epoxy Primer is an excellent sealer when reduced 25% with 162, 163 urethane reducer. When using as a sealer do not reduce with 161 Fast Urethane Reducer.
What can I use to reduce epoxy primer?
Clean good with lacquer thinner. I don’t think acetone or mineral spirits are strong enough for epoxy. I always reduced epoxy with lacquer thinner.
Can you put reducer in epoxy primer?
For the most part urethane grade reducer is pretty much universal as it can be used in epoxy primer, urethane primer, polyester primer, SS paint, most base coats, some clears..
Can you reduce epoxy primer with urethane reducer?
According to the tech sheet you can reduce it with Urethane Grade Reducer. I wouldn’t put paint thinner in anything. ’68 Coronet R/T wrote: According to the tech sheet you can reduce it with Urethane Grade Reducer.
Do I need to thin epoxy primer?
You need to thin the epoxy (by the remendations) and maybe better gun or smaller tip to get it to atomize better. But this is standard practice in collision shops all over the country. It works, so SOMETHING you are doing is wrong.
Is epoxy primer safe to spray?
When an epoxy primer is sprayed and is airborne it should be treated with the same respect as a 2 pack paint. Required Protection: If you’re spraying (or near someone spraying) epoxy primer then you need full respiratory protection. Check with the manufacturer of the primer to see what you need).
What is epoxy primer?
It is an airtight sealer that protects the primer before the walls are ready for paint. It also acts as a binding ingredient between the concrete, and the topcoat of the paint. Epoxy primer paint protects the walls from extreme weather conditions.
Can I use acetone to thin epoxy primer?
When using acetone or paint thinner for thinning epoxy, the general rule of thumb is a maximum of 10% added to the epoxy resin. An example would be if you had 32 ounces of epoxy that you were mixing you would only add up to 3.2 ounces of acetone to that mixture. Recommend over acetone and other solvents.
What is a epoxy reducer?
Rated 5.00 out of 5 based on 2 customer ratings. AquaGuard Epoxy Reducer can be used in place of Toluene to thin specified oil-based paint, lacquer, varnish, epoxy, adhesives and synthetic enamels when a slower rate of evaporation is desired. AquaGuard Epoxy Reducer will also remove certain adhesives.
How do you thin epoxy paint?
Paint Thinner or Acetone The general rule of thumb is to mix in thinner at a ratio of 10 to one. So, if you have 10 gallons of epoxy resin, then thin it using one gallon of paint thinner or acetone.
Do you thin car primer?
Most primers will have their own recommended ratio of paint thinner to primer. Many people will use half thinner and then half primer. Primer normally has a ration of 2 to 1 so you need 2 parts primer to 1 part thinner.
Will acetone damage cured epoxy?
Use enough acetone to soak into the surface a bit. Be careful not to damage the wood/concrete as you use your knife or scraping tool to gently and slowly scrape off the epoxy resin. There is no need to worry about any wet areas left by the acetone as it will evaporate on its own.
How thin can you pour epoxy resin?
As long as you pour in 1/8″ layers, you can go as thick as you like. The reason we recommend this thickness is two-fold: first, it allows the bubbles to escape properly, and second, it avoids any excessive overheating of the resin. So for best results always pour in a 1/8″ layer, and you’re good to go!Feb 6, 2021.
Is epoxy primer thick?
The epoxy primer should be applied in medium wet coats, allowing a half an hour between each coat at around 70 degrees. One to two coats will render a one millimeter dry film thickness, which is typically enough to be completely effective.
How long can you leave epoxy primer?
epoxy can sit just about forever but if it sets more than a couple days you should sand it and spray a coat of reduced epoxy as a sealer. most epoxies these days have around a 7 day recoat window but the more you wait the worse the adhesion is. i always like to get something on it within 24-48 hours.
Can you spray base coat over epoxy primer?
Base over fresh epoxy is the best way to do it. Reduce your epoxy 1:1:1 so it is a thin “sealer” coat and it lays down texture free. Sand to atleast 320 before epoxy sealer.
What is the difference between self etching primer and epoxy primer?
Self etching primer bonds well to bare metal surfaces and can be top coated in a short period of time. Epoxy primer can be applied in heavy coats which can be guide coated and block sanded to remove small imperfections in the body. Epoxy primer takes longer to dry (cure) before it can be sanded or top coated.
Do you have to sand epoxy primer?
If the thinner/reducer rag does not have any epoxy primer transfered to it then the epoxy is “cured” and needs to be sanded.
Does epoxy paint need a primer?
One of the most common questions I get with epoxy floors is if it is necessary to prime the floor before applying the epoxy floor coat. The right primer will guarantee better adhesion of your floor coats to the substrate. It will give your floor a longer life and will reduce the risk of the coat chipping or breaking.
