Table of Contents
Pour Glaze Coat IMMEDIATELY onto the center of the surface to be covered. Do not allow it to “sit“. You have about 15-20 minutes working time before product begins to harden. Spread the mixture over the area with a plastic spreader, plastic squeegee, notched trowel or brush.
Do you sand between glaze coats?
Glaze Coat can only be cleaned while it is still in a liquid state. After it has cured, paint remover, heat gun or sanding is required.
How long does it take Famowood to cure?
Allow fresh pours to cure in a warm room (at least 70 °F). Glaze Coat will fully cure in 72 hours. An additional 1 – 2 coats may be applied after 4 – 5 hours.
How long does glaze coat take to dry?
A full cure takes 24 to 72 hours, depending on the surrounding environment. With lower temperatures and higher humidity, cure time increases; with higher temperatures, cure time decreases. To speed drying time, apply heat using a handheld dryer set on low. Hold dryer at least 6 inches from the surface.
Is glaze coat the same as epoxy?
Famowood Glaze Coat is a pour-on epoxy coating. This ultra-clear, high-gloss finishing epoxy is ideal for home improvement and craft projects. Just one coat equals 60 coats of varnish. Glaze Coat is great for coating tables, bar tops, preserving pictures and photographs or imbedding items such as coins or rocks.
Does glaze need a top coat?
ANSWER: Yes! Even though General Finishes Milk Paint does not require a top coat for light to medium wear, once Glaze Effects is added GF recommends sealing the piece with High Performance. Think of stains and glazes as the color, and the topcoat as the protectant.
Can you recoat glaze coat?
Yes, you can apply a second coat of resin if you need to fix a mistake or a surface imperfection. You can also pour multiple layers if you need to cover areas of high relief, if you’re pouring into a mold or if you simply like the look of a thicker coat.
How many coats of Glaze Coat do I need?
FAMOWOOD GLAZE COAT HIGH BUILD EPOXY COATING is an ultra-clear, high gloss finish epoxy versatile enough to be used on just about any surface, either smooth or rough, stained or painted. This easy-to-use, 1:1 ratio is ideal for household and craft projects – just one pour equals 70 coats of varnish.
Does Glaze Coat smell?
This epoxy also has little to no odor which is a great benefit of this product since it is meant for indoor use. There may be some bubbling with this product though, so you’ll want to have a heat gun or torch available to coax the bubbles out.
Is Famowood glaze coat waterproof?
Glaze Coat® is a pour-on, high-gloss finishing epoxy that is perfect for home improvement, craft and woodworking projects. The ultra-clear, two-part Glaze Coat features an easy 1:1 ratio mix that yields a durable, waterproof and heat resistant coating equal to about 60 coats of varnish at 1/16″ thick. .
Why is it necessary to shake stir the glaze before applying it?
However, as materials in some glazes tend to settle after standing, it is important to shake or agitate the container vigorously, then stir, before use. If after shaking and stirring the glaze it is still too thick to load a glaze brush easily then it may be necessary to add a little water.
Does glaze go bad?
Glazes do not ‘go bad’ with age but, because different ingredients tend to come out of suspension at different rates, it is critical that the batch or bottle be mixed thoroughly before each application. Single firing (glaze applied to greenware) is not recommended with today’s glazes.
Is Glaze Coat flexible?
The Glaze Coat is tough, yet flexible to avoid shattering on impact. Impressions usually disappear in a few hours at normal 72-75 °F room temperatures.
Can you put polyurethane over glaze coat?
5. Apply at least two coats of water-based poly in order to protect your surface. Make sure that you use water-based polyurethane over water-based glazes and oil-based over oil glazes for consistency.
What is glaze coat used for?
FAMOWOOD Glaze Coat is a pour-on epoxy coating that can be used on most surfaces – rough or smooth, stained or painted. It’s great for coating tables or bar tops, preserving photographs or imbedding decorative items.
Do you seal over glaze?
Do I Need To Seal After Applying Glaze? In some cases, the Glaze will work fine as a sealer along with the coat of Top Coat that you’ve already applied. However, if your furniture is going to be used often, we recommend applying another 2-3 layers of Top Coat sealer on top of the Glaze finish.
Is glaze a sealer?
Glazes are designed to fill in minor scratches and reduce the appearance of imperfections. Traditional glazes are formulated to help you perfect your paintwork by filling in those minor scratches. After you applied glaze to your car, you would then finish with – yup, you guessed it – a sealant.
Can I paint over glaze?
Glaze refers to a clear acrylic solution that can be added to paint to make it more transparent and keep it from drying quickly. In most cases, the glaze is water-based and will cause no problems if you paint over it with a latex, or water-based, paint.
Can you put polyurethane over Famowood glaze coat?
To coat over polyurethane or acrylic finishes, lightly sand the surface and wipe with acetone or alcohol before using Glaze Coat. To catch drips, cover surrounding area with waxed paper or drop cloth. Allow drips to flow freely off the sides by elevating area to be coated.
Should you sand between coats of epoxy?
Sanding will not only get out the imperfection but will also serve to provide some tooth between the first and second layers. It will look very scuffed in the short term but do not worry, once you pour the second coat over top, all of those sanding marks will disappear.
